ELRS vs SBUS: What Is the Difference for Your FPV Drone?
You are shopping for a tinywhoop or an FPV drone and the product page offers two versions: ELRS or SBUS. Same price or close to it, same drone, but not at all the same way of flying it. Pick the wrong version and you end up with a drone none of your radios can control. Here is the difference, without the jargon.
The short answer
ELRS (ExpressLRS) is a radio link: it is how your radio controller talks to the drone, through the air. SBUS is a wired protocol: it is how a receiver talks to the flight controller, inside the drone, over a wire. So they are not really competitors: they work at different stages of the control chain.
When a manufacturer sells an "ELRS version" and an "SBUS version", what it is really telling you is which radio controller will fly the drone.
Understanding the control chain of an FPV drone
When you move a stick, the signal goes through three steps:
- The radio controller sends the command over radio waves.
- The receiver, on board the drone, picks up that command.
- The flight controller (Betaflight) gets the command from the receiver and drives the motors.
ELRS covers step 1 to 2 (the wireless link). SBUS covers step 2 to 3 (the wired link). That is the whole key to the question.
ELRS: the open-source radio link that became the standard
ExpressLRS is an open-source radio protocol that appeared in 2020 and took over FPV within a few years. Its strengths:
- Very low latency and high refresh rates (up to 500 Hz and beyond depending on the hardware), which gives a very direct feeling of control.
- Long range for modest transmit power.
- Cheap, universal hardware: most current radios (RadioMaster Pocket, Boxer, BETAFPV LiteRadio and others) have a built-in 2.4 GHz ELRS module.
- The receiver is often built into the flight controller board on tinywhoops, so there is nothing to wire.
Worth knowing: between the ELRS receiver and the flight controller, the conversation usually runs over a protocol called CRSF, not SBUS.
SBUS: the old wired standard brought back by DJI
SBUS was created by Futaba to carry up to 16 channels over a single wire between a receiver and a flight controller. For years it was the standard for many receivers (FrSky, Futaba). It is slower than modern links, but more than enough for leisure and cinematic flying.
It is back on product pages mainly because of the DJI ecosystem. With a DJI O4 video unit, the video system itself carries the commands: you fly with a DJI radio (DJI FPV Remote Controller 2 or Remote Controller 3), the signal goes through the goggles and the Air Unit, and the Air Unit passes it to the flight controller over SBUS. No separate radio receiver needed.
ELRS vs SBUS: comparison table
| ELRS version | SBUS version (DJI) | |
|---|---|---|
| Role | Radio link, radio controller to drone | Wired link, Air Unit or receiver to flight controller |
| Compatible radio | Any ELRS radio (RadioMaster, BETAFPV, Jumper and others) | DJI FPV Remote Controller 2 or 3 |
| Perceived latency | Very low | Slightly higher, fine for cinematic flying |
| Ecosystem | Open, multi-brand | Closed, all DJI |
| Who it is for | Pilots who want to progress in freestyle or already own an ELRS radio | Pilots already on DJI gear who want a simple setup |
Which one should you choose?
Choose the SBUS version if you already have (or plan to buy) O4-compatible DJI goggles and a DJI FPV RC2 or RC3 radio. Everything binds inside the same ecosystem, with no radio module to configure.
Choose the ELRS version if you already own a RadioMaster-type radio, if you fly a simulator with that radio, or if you want to fly demanding freestyle. It is also the most future-proof choice: an ELRS radio will fly almost all your future drones, whatever the brand. The RadioMaster AX12 is one example.
The simple rule: start from the radio you have, and buy the drone version that matches it. Doing it the other way round often costs you an extra radio.
A real example: the Meteor75 Pro II O4, SBUS version
The BETAFPV Meteor75 Pro II with DJI O4 Air Unit Wide (SBUS version) is a textbook case. It is a 75 mm 1S tinywhoop, about 37 g, that records stabilised 4K thanks to the O4. In SBUS version it is flown directly with a DJI FPV Remote Controller 2 or 3, paired with O4-compatible goggles (Goggles 3, Goggles N3, Goggles 2 or Goggles Integra). It ships with 4 x 1S batteries and a charger from our EU warehouse.
If you already live in the DJI world, it is the most direct way to fly indoors and bring back clean footage without touching a radio receiver. To go further, read our full Meteor75 Pro II O4 review.
Have an ELRS radio instead? Look at the Meteor75 Pro analogue ExpressLRS 2.4G.
FAQ
Can you convert an SBUS drone to ELRS?
Yes, by adding an external ELRS receiver wired to the flight controller and configuring it in Betaflight. It is doable but needs soldering on a tinywhoop: better to buy the right version from the start.
Is SBUS outdated?
As a classic receiver protocol it has largely been replaced by CRSF/ELRS. But in the DJI ecosystem it remains the standard way to pass commands from the Air Unit to the flight controller.
Can an ELRS radio fly an SBUS-version drone?
Not directly. The SBUS version expects commands from the DJI Air Unit, so from a DJI radio. You would have to add a receiver compatible with your radio.
What is the best option for a beginner?
For a beginner starting from zero, an ELRS radio is the most versatile investment: it works on simulators and on most FPV drones. If you already own DJI goggles and a DJI RC, the SBUS version is the simplest to get flying.